\n \nOwning a Honda Element comes with all kinds of wonderful things, but encountering the P2646 and/or P2647 codes sure isn't one of them.  The resulting "limp mode" can ruin any drive. Tracking down the issue can be a daunting experience. Don't fret; let's dive deeper into understanding and troubleshooting this persistent issue. \n \nIf you're facing the persistent P2646 and P2647 codes in your Honda Element, causing the engine to enter "limp mode" at approximately 3,000 RPM, you're not alone. Contrary to common misconception, these codes aren't linked to a speed governor but are a result of low oil pressure at the VTEC oil pressure switch. \n

Troubleshooting Steps

\nHere are suggestions, ordered from least complex and costly to more involved solutions: \n

Check Oil Level:

\nInadequate oil levels can trigger these codes. Sometimes, a refill or oil change followed by code reset can resolve the issue. \n

Reset the Code:

\nIf you're sure you have enough oil in the car, using a code scanner to reset the code can buy you some time.  It can get you to you destination and allow you some time to investigate some more. \n

Moisture-Related Electrical Checks:

\n

\n
• If the problem arises post-rain or exposure to moisture, it likely involves an electrical issue compounded by water.
\n
• Examine wire harnesses for loose connections, seal wire entry points with high-temperature sealant like Hondabond to prevent water from getting in the connections.
\n
• Disconnect harnesses, use compressed air to remove moisture, and apply dielectric grease for better connections.
\n
• Consider harness replacement if needed.
\n

\n

Potential System Clogs:

\nClogs might exist in various parts of the VTEC system, particularly in two screens: \n

\n
• First Screen (VTEC Solenoid): Remove the solenoid using a 10mm wrench or socket.  There are three bolts holding it in place.  You'll have to feel around to locate them. Inspect the screen for debris or damage, and replace if necessary (part number: Honda 15815-RAA-A02 Filter Assy., Spool Valve).
\n
• Second Screen (Behind Power Steering Pump): Accessing this screen is more complex, requiring belt and pump removal. Check and clean if the first screen indicates significant clogging (part number: Honda 15845-RAA-A01 Filter Assy., Vtc).
\n

\n

Solenoid Replacement:

\n

\n
• If you're looking to save money, this will be your last resort.
\n
• Only use OEM parts like the Honda 15810-RAA-A03 Valve Assembly, Spool, to ensure reliability.
\n
• Over-tightening the bolts on installation, can cause damage to the screen.  Use 8 pound torque or hand tight plug another 1/4 to 1/2 turn.
\n

\n

Beware Counterfeit Solenoids

\n

\n
• Only buy from trusted sources or authorized dealers, as cloned parts flood the market.
\n
• Genuine replacements can cost around $245 or more.
\n
• Your best bet is to get it from a dealer (I also have them on my site).  If you start surfing amazon or ebay, you’re taking a gamble.  There are a lot of clones out there that claim to be OEM but they are not.
\n
• They are becoming unavailable at many providers so I would expect the price to keep going up. If the price is significantly lower than $200,  you’re likely being scammed.
\n
• You used to be able to tell the OEM one apart from the others based on the star shape of the head of the bolt at the top of the unit, but even that it’s always enough anymore.
\n
• Scammers may show an OEM one in the picture but ship you a clone.
\n

\n

Conclusion

\nRegular maintenance and diligent troubleshooting are key to addressing the P2646 and P2647 codes in your Honda Element. By paying attention to oil levels, moisture exposure, and potential system clogs, you can effectively resolve this issue and restore your vehicle's performance without breaking the bank. \n \n